OSHA compliance training you may visit PEO. To start and implement a comprehensive safety program for your company contact Robert Breakiron at rbreakiron@nationalpeo.com. By: Robert Breakiron Safety Manager, National PEO References: Federal OSHA Arizona Department of Occupational Safety and Health ">During the years I have been involved in the EH&S sector of business I am amazed at the attitude many companies and management take toward safety and compliance with OSHA standards. In many cases the general attitude is “I am a small company with only fifteen employees’, OSHA isn’t going to take time to visit me”. Other attitudes management takes toward a safety program are “Safety is a money pit with no return on the dollar and it adds to the cost of doing business”, “I can’t afford to have employees take a half hour a month for safety training”, “I can’t afford to implement a safety program”.
Unfortunately and sadly many employees of both small and large companies pay the price by being injured, permanently disabled or worse, losing their lives needlessly. Beside the false belief that safety costs money many companies and managers are also willing to roll the dice that no serious accidents are going to happen and OSHA will not pay them a visit.
The General Duty Clause of the OSHA Standard states that “Each employer shall furnish to each employee of his place of employment which is free from recognized hazards that are causing or are likely to cause death or serious harm to employees”. When an OSHA compliance officer shows up to your business to conduct a compliance inspection they are not there to hassle or make your life miserable and shut your business down. They are conducting the inspection to ensure you the employer are providing a safe and healthful work environment for your employees. Under federal law OSHA can not shut down or cease a business, however, they can issue citations and levy monetary penalties. Depending on how your business fairs during the compliance inspection will determine the type of citations and penalties issued. What management also must consider the standards the company is found not in compliance with and a penalty has been levied, besides paying the penalty, the company must also abate and correct the cited violations. This must be done by the abatement date on the citation for each type of violation, not when management decides they will get around to it. Failure to abate and correct the hazards may also lead to additional penalties on a daily basis until the hazards are corrected.
For the safety professional, changing the mindset of management about safety can sometimes be the same as running into a brick wall. When management is presented statistical and financial data on what accidents and injuries are actually costing the company they will usually sit back and take a different view of safety. Your company comptroller, workers compensation carrier, company liability carrier and OSHA will all support the fact that a comprehensive safety program pays dividends more ways than one. In a recent newsletter published by ADOSH (Arizona Department of Occupational Safety and Health) they estimate that for every dollar invested in a comprehensive safety program, an employer can realize a return of up to four dollars. Where else in todays or tomorrows business world can companies get that kind of return on an investment?
Any accident resulting in an injury has a direct affect on the bottom line of any size company. Take for example a business operating at a twenty percent profit having only one injury resulting in a workers compensation claim of only $495. The total direct and indirect cost of that accident would be approximately $2,722 which would require the company to generate an additional $13,610 is sales to cover the injury. This is the cost of not having a safety program in place to eliminate hazards, training employees in safety and reducing accidents. This goes to prove that the absence of a safety program cost money and a comprehensive safety program could be viewed as a profit center.
For companies who don’t know the process of implementing a safety program or what the OSHA standards are there is plenty of help in the business world to choose from and some of it is free. There are private consultants, PEO’s, professional organizations and OSHA, yes I said OSHA.
For more information on OSHA compliance training you may visit PEO. To start and implement a comprehensive safety program for your company contact Robert Breakiron at rbreakiron@nationalpeo.com. By: Robert Breakiron Safety Manager, National PEO References: Federal OSHA Arizona Department of Occupational Safety and Health
Full Hazwoper Safety Courses Online
Wednesday, November 12, 2008
Online CE - OSHA 10 Hour Safety Course
The Occupational Safety and Health Administration's (OSHA) 10 Hour Course is the building block of any accident and safety prevention training program in the workplace.
This 10 hour course is designed for construction workers, foremen, job supervisors, and anyone involved in the construction or general industry. OSHA recommends Outreach Training Program courses as an orientation to occupational safety and health for workers.
Workers must receive additional training, when required by OSHA standards, on the specific hazards of the job. Upon successful completion of the OSHA 10 Hour course, participants will receive an OSHA construction safety and health 10- hour course completion card from the Department of Labor. There is no previous safety training or experience required for this course.
The 10 Hour classes emphasize hazard identification, avoidance, control, and prevention. Topics include an introduction to OSHA, electrical standards, and fall protection. Other topics include excavation, scaffolding, tool safety, materials handling, ladder safety, crane and hoist safety, and personal protective equipment.
This safety course has proven to be highly successful in reducing the number of on-the-job accidents and OSHA considers this course their “primary way to train workers in the basics of occupational safety and health.”
OSHA outreach training can be delivered via in-person training or, if approved by OSHA, via online training. OSHA has specific guidelines for on-line safety training, and there are only a few on-line safety programs that OSHA has allowed. Make sure any online program has been reviewed and accepted by OSHA for online distribution.
Online safety training has a number of advantages. Employees (students) can train "anytime, anywhere" in the world-whenever there is an internet connection. No more lost time from work travelling to distant seminars. Business travelers can train while working out of town. Employees who work night shifts don't have to lose sleep to attend classes. No matter what your work schedule, online safety training can work for you.
Many online safety course providers allow employee to train at their own pace. Course can be started and stopped by the student when it is most convenient for them. Make sure you can pick up your place where you left off (bookmarking).
Most online training is affordable. Corporations save between 50-70% due to elimination of travel expenses according to Training Magazine. By training online you can eliminate costly hotel stays and training rooms, costly instructors and other incidentals that add up big time! Individuals save time and money travelling to and from home or business to the training site as well.
Peter Altuch, President HR Training University www.hrtraininguniversity.com info@hrtraininguniversity.com “OSHA reviewed and accepted for online distribution”
OSHA General Training School - Courses for 8 hour, 24 hour and 40 hr training
This 10 hour course is designed for construction workers, foremen, job supervisors, and anyone involved in the construction or general industry. OSHA recommends Outreach Training Program courses as an orientation to occupational safety and health for workers.
Workers must receive additional training, when required by OSHA standards, on the specific hazards of the job. Upon successful completion of the OSHA 10 Hour course, participants will receive an OSHA construction safety and health 10- hour course completion card from the Department of Labor. There is no previous safety training or experience required for this course.
The 10 Hour classes emphasize hazard identification, avoidance, control, and prevention. Topics include an introduction to OSHA, electrical standards, and fall protection. Other topics include excavation, scaffolding, tool safety, materials handling, ladder safety, crane and hoist safety, and personal protective equipment.
This safety course has proven to be highly successful in reducing the number of on-the-job accidents and OSHA considers this course their “primary way to train workers in the basics of occupational safety and health.”
OSHA outreach training can be delivered via in-person training or, if approved by OSHA, via online training. OSHA has specific guidelines for on-line safety training, and there are only a few on-line safety programs that OSHA has allowed. Make sure any online program has been reviewed and accepted by OSHA for online distribution.
Online safety training has a number of advantages. Employees (students) can train "anytime, anywhere" in the world-whenever there is an internet connection. No more lost time from work travelling to distant seminars. Business travelers can train while working out of town. Employees who work night shifts don't have to lose sleep to attend classes. No matter what your work schedule, online safety training can work for you.
Many online safety course providers allow employee to train at their own pace. Course can be started and stopped by the student when it is most convenient for them. Make sure you can pick up your place where you left off (bookmarking).
Most online training is affordable. Corporations save between 50-70% due to elimination of travel expenses according to Training Magazine. By training online you can eliminate costly hotel stays and training rooms, costly instructors and other incidentals that add up big time! Individuals save time and money travelling to and from home or business to the training site as well.
Peter Altuch, President HR Training University www.hrtraininguniversity.com info@hrtraininguniversity.com “OSHA reviewed and accepted for online distribution”
OSHA General Training School - Courses for 8 hour, 24 hour and 40 hr training
Thursday, September 11, 2008
OSHA Safety Training: Construction
Safety training within the construction work environment is vital to the company and more importantly for the well being of the workers. As long as safety and health regulations are properly followed, construction can be safe regardless of its high fatality rate. There are three main concerns for construction companies to pay close attention to such as falls, electrical accidents, trenching and being hit by a vehicle. If these areas are emphasized to employees as being the most dangerous then the workers will pay more attention while in these circumstances. Total construction fatalities rose by 9.1 percent in 2004, from 1131 to 1234, which reinforces the need for proper safety awareness and training.
Falls
Falls are the most prevalent work-related deaths in the construction field. In 1999, an average of 362 deaths was caused by falling on the job. Many construction sites have unprotected opening that is could cause a fatal fall. If the drop is more than six feet to the next lower level there should be some sort of protection. If the hazardous drop is the result of no wall on one side or all sides of a building, the company should build guardrails on all sides where workers could easily fall. When working on a building that requires fixing or replacing a roof, the best option is to implement a safety net under the roof. This will easily catch anyone who falls from losing their balance. Suppose the job site is located at an extremely building, the most effective protection gear would be a fall arrest system. The fall arrest system will stop up to 1800 pounds of force. Other implementable strategies include: evaluate new construction sites before work starts and guard all of the existing holes, cover holes as soon as they form on sites; successfully assemble the hole-guards to hold employees, equipment, and materials. Companies should put into practice covering holes and using either the guardrail, safety net, or personal fall arrest systems together.
Electrical Accidents
There are five main reasons that electrical incidents occur: working around power lines, lack of ground-fault protection, ground path is lost or broken, improper use of equipment, not using extension or flexible cords correctly. When starting up a new job or continuing an old one, there are many precautions to follow. Survey each job site and recognize overhead power lines and do not come within ten feet of them. De-energize lines when working near them. Set up warning signs near buried and visible power lines. Use ground-fault circuit interrupters on all 120-volt, single phase, and 15-20 ampere receptacles. Make sure that all power supplies, circuits, and electrical equipment are grounded. Regularly examine electrical systems to assure that the path is continuously grounded. Never take off protective prongs from connected equipment. Always work with double-insulated tools and ground all metal parts of the equipment. Lastly, make sure that every worker has been trained on how to use equipment correctly and is in functioning condition.
Hit by Vehicles
Over 75% of struck-by deaths are caused by the heavy machinery and equipment. To avoid vehicle related accidents one should follow these procedures: always wear a seat belt; look for other vehicles before every shift; never drive a vehicle if it is not possible to see out of the back; only drive vehicles on safe terrain; never dump loads while people are close by; always use the parking break when leaving the vehicle; inspect the breaks regularly; never surpass a vehicles capacity; and use traffic signs, barricades, and/or flaggers while construction is in process. If the previous list is followed on an everyday basis, construction injuries and deaths could significantly decrease.
To learn more about safety training which helps small businesses comply with rules and city regulations visit our expert site at www.safetyservicescompany.com
Falls
Falls are the most prevalent work-related deaths in the construction field. In 1999, an average of 362 deaths was caused by falling on the job. Many construction sites have unprotected opening that is could cause a fatal fall. If the drop is more than six feet to the next lower level there should be some sort of protection. If the hazardous drop is the result of no wall on one side or all sides of a building, the company should build guardrails on all sides where workers could easily fall. When working on a building that requires fixing or replacing a roof, the best option is to implement a safety net under the roof. This will easily catch anyone who falls from losing their balance. Suppose the job site is located at an extremely building, the most effective protection gear would be a fall arrest system. The fall arrest system will stop up to 1800 pounds of force. Other implementable strategies include: evaluate new construction sites before work starts and guard all of the existing holes, cover holes as soon as they form on sites; successfully assemble the hole-guards to hold employees, equipment, and materials. Companies should put into practice covering holes and using either the guardrail, safety net, or personal fall arrest systems together.
Electrical Accidents
There are five main reasons that electrical incidents occur: working around power lines, lack of ground-fault protection, ground path is lost or broken, improper use of equipment, not using extension or flexible cords correctly. When starting up a new job or continuing an old one, there are many precautions to follow. Survey each job site and recognize overhead power lines and do not come within ten feet of them. De-energize lines when working near them. Set up warning signs near buried and visible power lines. Use ground-fault circuit interrupters on all 120-volt, single phase, and 15-20 ampere receptacles. Make sure that all power supplies, circuits, and electrical equipment are grounded. Regularly examine electrical systems to assure that the path is continuously grounded. Never take off protective prongs from connected equipment. Always work with double-insulated tools and ground all metal parts of the equipment. Lastly, make sure that every worker has been trained on how to use equipment correctly and is in functioning condition.
Hit by Vehicles
Over 75% of struck-by deaths are caused by the heavy machinery and equipment. To avoid vehicle related accidents one should follow these procedures: always wear a seat belt; look for other vehicles before every shift; never drive a vehicle if it is not possible to see out of the back; only drive vehicles on safe terrain; never dump loads while people are close by; always use the parking break when leaving the vehicle; inspect the breaks regularly; never surpass a vehicles capacity; and use traffic signs, barricades, and/or flaggers while construction is in process. If the previous list is followed on an everyday basis, construction injuries and deaths could significantly decrease.
To learn more about safety training which helps small businesses comply with rules and city regulations visit our expert site at www.safetyservicescompany.com
Wednesday, February 20, 2008
30 Hour Outreach Credit - 30 hr OSHA Course
Begin completing your OSHA requirements for outreach online course credits.
The OSHA 30 Hour General Industry Outreach Training course is a comprehensive safety program designed for anyone involved in general industry. Specifically devised for safety directors, foremen, and field supervisors; the program provides complete information on OSHA compliance issues. OSHA recommends Outreach Training Programs as an orientation to occupational safety and health for workers covered by OSHA 29 CFR 1910. General industry workers must receive additional training, when required by OSHA standards, on specific hazards of the job. Upon successful completion of the course, participants will receive an OSHA general industry safety and health 30-hour course completion card from the Department of Labor. Note: This online course has been reviewed and accepted by OSHA for online distribution.
REGULATORY REQUIREMENT:
Please see the state/regulatory requirement from the course catalog page.
This outreach course has been reviewed and approved for 30 hours.
The OSHA 30 Hour General Industry Outreach Training course does not have any pre-requisites; however, the OSHA 30 Hour General Industry Outreach training course or an equivalent of 30 hours of prior safety and health training plus 5 years of general industry safety and health experience is a prerequisite for the OSHA 501 Trainer course.
Upon successful completion of this course, you will receive a course completion card in the mail.
Quizzes - All quizzes must be passed with a 100% to proceed forward to the next lesson.
Final Exam- Final Exam must be passed with a 70% to pass the course. The final exam can be taken three times if necessary.
Outreach Training
The OSHA 30 Hour General Industry Outreach Training course is a comprehensive safety program designed for anyone involved in general industry. Specifically devised for safety directors, foremen, and field supervisors; the program provides complete information on OSHA compliance issues. OSHA recommends Outreach Training Programs as an orientation to occupational safety and health for workers covered by OSHA 29 CFR 1910. General industry workers must receive additional training, when required by OSHA standards, on specific hazards of the job. Upon successful completion of the course, participants will receive an OSHA general industry safety and health 30-hour course completion card from the Department of Labor. Note: This online course has been reviewed and accepted by OSHA for online distribution.
REGULATORY REQUIREMENT:
Please see the state/regulatory requirement from the course catalog page.
This outreach course has been reviewed and approved for 30 hours.
The OSHA 30 Hour General Industry Outreach Training course does not have any pre-requisites; however, the OSHA 30 Hour General Industry Outreach training course or an equivalent of 30 hours of prior safety and health training plus 5 years of general industry safety and health experience is a prerequisite for the OSHA 501 Trainer course.
Upon successful completion of this course, you will receive a course completion card in the mail.
Quizzes - All quizzes must be passed with a 100% to proceed forward to the next lesson.
Final Exam- Final Exam must be passed with a 70% to pass the course. The final exam can be taken three times if necessary.
Outreach Training
10 Hour Outreach Course - OSHA Online
Begin your 10 hr Outreach course training online.
OSHA - 10 Hour General Industry Outreach Training Program
This course is ideal for supervisors with safety and health responsibilities, and for employee safety and health awareness. Students will be introduced to OSHA policies, procedures and standards as well as general industry safety and health principles covered in OSHA Act Part 1910. Special emphasis will be placed on areas most hazardous using OSHA standards as a guide. Upon successful completion of the course, participants will receive an OSHA general industry safety and health 10-hour course completion card from the Department of Labor. Note: This online course has been reviewed and accepted by OSHA for online distribution.
State the purpose of the OSH Act and list the functions of OSHA
List the OSHA inspection priorities and describe the inspection process
Describe the rights and responsibilities of employers and employees under the OSH Act
The basic requirements for proper aisle and passageway maintenance
Guidelines for identification and protection of floor openings
To understand the importance of effective Egress fire protection program
To know the safe means of Egress to provide fire protection in emergencies from new or old buildings or structures
Outline the general requirements for general safety standards
Establish the guidelines and requirements for special purpose equipment
TOPICS COVERED:
Introduction to OSHA, OSH Act, Inspections, Citations, and Penalties
Walking and Working Surfaces
Means of Egress and Fire Protection
Electrical
Flammable and Combustible Liquids
Personal Protective Equipment
Machine Guarding
Hazard Communication
Introduction to Industrial Hygiene/ Bloodborne Pathogens
Safety & Health Programs
REGULATORY REQUIREMENT:
Please see the state/regulatory requirement from the course catalog page.
SEAT TIME:
This course has been reviewed and approved for 10 hours.
COURSE PRE-REQUISITE:
N/A
COMPLETION:
Upon successful completion of this course, you will receive a course completion card in the mail.
TESTING:
Quizzes - All quizzes must be passed with a 100% to proceed forward to the next lesson.
Final Exam- Final Exam must be passed with a 70% to pass the course. The final exam can be taken three times if necessary.
Outreach 10 Hr Course Credit - View sample and outline
OSHA - 10 Hour General Industry Outreach Training Program
This course is ideal for supervisors with safety and health responsibilities, and for employee safety and health awareness. Students will be introduced to OSHA policies, procedures and standards as well as general industry safety and health principles covered in OSHA Act Part 1910. Special emphasis will be placed on areas most hazardous using OSHA standards as a guide. Upon successful completion of the course, participants will receive an OSHA general industry safety and health 10-hour course completion card from the Department of Labor. Note: This online course has been reviewed and accepted by OSHA for online distribution.
State the purpose of the OSH Act and list the functions of OSHA
List the OSHA inspection priorities and describe the inspection process
Describe the rights and responsibilities of employers and employees under the OSH Act
The basic requirements for proper aisle and passageway maintenance
Guidelines for identification and protection of floor openings
To understand the importance of effective Egress fire protection program
To know the safe means of Egress to provide fire protection in emergencies from new or old buildings or structures
Outline the general requirements for general safety standards
Establish the guidelines and requirements for special purpose equipment
TOPICS COVERED:
Introduction to OSHA, OSH Act, Inspections, Citations, and Penalties
Walking and Working Surfaces
Means of Egress and Fire Protection
Electrical
Flammable and Combustible Liquids
Personal Protective Equipment
Machine Guarding
Hazard Communication
Introduction to Industrial Hygiene/ Bloodborne Pathogens
Safety & Health Programs
REGULATORY REQUIREMENT:
Please see the state/regulatory requirement from the course catalog page.
SEAT TIME:
This course has been reviewed and approved for 10 hours.
COURSE PRE-REQUISITE:
N/A
COMPLETION:
Upon successful completion of this course, you will receive a course completion card in the mail.
TESTING:
Quizzes - All quizzes must be passed with a 100% to proceed forward to the next lesson.
Final Exam- Final Exam must be passed with a 70% to pass the course. The final exam can be taken three times if necessary.
Outreach 10 Hr Course Credit - View sample and outline
Subscribe to:
Posts (Atom)